04-11-2016, 03:11 PM
Lots of posts to reply to, i'll try and get it all in! Firstly the OPT I was originally using was indeed a "RS Standard Universal OPT - 217-567". I estimate it was made circa 70/80's. It has a "datasheet" which gives rough Z pri for various loads dependant on what pins you connect it to. I had it connected 1-3 pri/D-A sec. I did measure Vin/out and worked out a Z pri of 6700, I think. I presumed it was made for SE use but after what Andy Radioman said post #30, I notice it has a CT column, therefore it was intended for P-P use too. I'm no longer using it as the OP was rubbish maybe due to core saturation. I have a Marconi TF2700 , I will measure the L.
Re the ECC voltage amp - Kalee, well spotted, another bog up on my part, your right, I did a 2v input. Some of these old graph's are hard to use because of the scale, good idea Lawrence to measure using mm. One thing though, we don't need to be 100% accurate ( it's a valve amp not a precision measuring device) and can't really be as the graph represents an ideal valve not the one were using. I see your points, 47k would be better. What I'm puzzled by is that if we use a ECC83 we get 60v P-P out, which I thought would overdrive the OP valve causing distortion. Also wouldn't it mean that the volume knob would only go to "3" say? I thought to design a voltage amplifier stage we need an OP whatever the following valves g1 bias is + a bit extra for losses due to following g1 resistor and valve capacitance etc.
"The µ of a triode is a pretty reliable and constant characteristic. But mutiual conductance gm isn't. So if you use a really low value of anode load (like 1kΩ) the gain is going to be small and virtually dependent on gm, with the prospect of distortion as you run around the foot of any curve. Whereas if you use a very large value of anode load, like 100kΩ, or even better a constant-current load or a really high-value inductor, then the gain approaches µ which, being constant, implies low distortion. " There is far more than meets the eye to making a voltage amp stage than drawing a load line and choosing a bias point, I didn't know this Kalee. When doing it myself I've tried to chose a load and bias point so the operating point falls on the straight part of the grid line and avoid the curved part.
Post #29 - yes u, gm and dynamic anode resistance inter relate I think the word is. You can find out the dynamic anode resistance too by graphical analysis. There's no equivalent process for a transistor AFAIK. See Radio Designers Handbook- F Langford Smith, Chapter 2 Section 1 page 13. Thanks for the other link Lawrence.
Armed with all your advice I'll try and get time over the weekend to iron out the last wrinkles.
Thanks again, Andy.
Re the ECC voltage amp - Kalee, well spotted, another bog up on my part, your right, I did a 2v input. Some of these old graph's are hard to use because of the scale, good idea Lawrence to measure using mm. One thing though, we don't need to be 100% accurate ( it's a valve amp not a precision measuring device) and can't really be as the graph represents an ideal valve not the one were using. I see your points, 47k would be better. What I'm puzzled by is that if we use a ECC83 we get 60v P-P out, which I thought would overdrive the OP valve causing distortion. Also wouldn't it mean that the volume knob would only go to "3" say? I thought to design a voltage amplifier stage we need an OP whatever the following valves g1 bias is + a bit extra for losses due to following g1 resistor and valve capacitance etc.
"The µ of a triode is a pretty reliable and constant characteristic. But mutiual conductance gm isn't. So if you use a really low value of anode load (like 1kΩ) the gain is going to be small and virtually dependent on gm, with the prospect of distortion as you run around the foot of any curve. Whereas if you use a very large value of anode load, like 100kΩ, or even better a constant-current load or a really high-value inductor, then the gain approaches µ which, being constant, implies low distortion. " There is far more than meets the eye to making a voltage amp stage than drawing a load line and choosing a bias point, I didn't know this Kalee. When doing it myself I've tried to chose a load and bias point so the operating point falls on the straight part of the grid line and avoid the curved part.
Post #29 - yes u, gm and dynamic anode resistance inter relate I think the word is. You can find out the dynamic anode resistance too by graphical analysis. There's no equivalent process for a transistor AFAIK. See Radio Designers Handbook- F Langford Smith, Chapter 2 Section 1 page 13. Thanks for the other link Lawrence.
Armed with all your advice I'll try and get time over the weekend to iron out the last wrinkles.
Thanks again, Andy.







