I was about to hit the sack late last night...then I got to wondering...a niggling feeling, nowt for it, I had to get the other two veneers out to have a look, suprisingly they came out quite easy as the fixing pins were well rusted through, the thinnest veneer came out first, it's the same thickness as the first one I took out a couple of days ago (the rear one).
That revealed the middle veneer, about 25mm in from the right hand side there was what appeared to be a full length split running from top to bottom (grain orientated vertically) the other two veneers had the grain orientated horizontally.
So.....Originally it must have been plywood, I had a close look at the split and it turned out that it wasn't a split but a core join, all this might tie up with the bias battery, there's no front panel terminals for one, when I first aquired the receiver to look at there were four wires coming out of some holes in the cabinet base, they can be seen in the first set of pics I posted in this thread, three of them would make sense, two for the GB -ve for the two audio stages and the other for GB +ve, so what about the fourth wire....well that goes to the HT side of the 1st interstage transformer, it's the only wire that's connected to it, if you look at the 1st pic in the 3rd set of pics I posted you can see a wire with termination loop left unconnected on the end of it, it's wrapped round another wire and is located south east of the 1st interstage transformer in the pic, the other end of the wire with the loop is connected to the HT +ve terminal on the front panel, I'm 100% sure that the looped end was originally connected to the HT +ve side of the 1st interstage transformer.
So what does all this mean? Well at the moment I think that originally the receiver had a GB battery fitted internally (absence of GB terminals on front panel)
The plywood towards the rear of the cabinet was there to stop the roll top from fouling up on the GB battery and it's connecting wires (can't think of any other reason for it being there)
The holes in the base of the cabinet that the wires feed through look like later additions, they look rough eg suffered from breakthrough when being drilled, three of the wires coming out of the holes were for an external GB battery, the fourth wire coming out of one of the holes was for an external HT battery to supply the 1st audio amp for whatever reason, maybe when the Mullard series of valves were fitted.
I'm also thinking bright emitter valves (French TM) were originally fitted.
What do folks think?
Lawrence.
That revealed the middle veneer, about 25mm in from the right hand side there was what appeared to be a full length split running from top to bottom (grain orientated vertically) the other two veneers had the grain orientated horizontally.
So.....Originally it must have been plywood, I had a close look at the split and it turned out that it wasn't a split but a core join, all this might tie up with the bias battery, there's no front panel terminals for one, when I first aquired the receiver to look at there were four wires coming out of some holes in the cabinet base, they can be seen in the first set of pics I posted in this thread, three of them would make sense, two for the GB -ve for the two audio stages and the other for GB +ve, so what about the fourth wire....well that goes to the HT side of the 1st interstage transformer, it's the only wire that's connected to it, if you look at the 1st pic in the 3rd set of pics I posted you can see a wire with termination loop left unconnected on the end of it, it's wrapped round another wire and is located south east of the 1st interstage transformer in the pic, the other end of the wire with the loop is connected to the HT +ve terminal on the front panel, I'm 100% sure that the looped end was originally connected to the HT +ve side of the 1st interstage transformer.
So what does all this mean? Well at the moment I think that originally the receiver had a GB battery fitted internally (absence of GB terminals on front panel)
The plywood towards the rear of the cabinet was there to stop the roll top from fouling up on the GB battery and it's connecting wires (can't think of any other reason for it being there)
The holes in the base of the cabinet that the wires feed through look like later additions, they look rough eg suffered from breakthrough when being drilled, three of the wires coming out of the holes were for an external GB battery, the fourth wire coming out of one of the holes was for an external HT battery to supply the 1st audio amp for whatever reason, maybe when the Mullard series of valves were fitted.
I'm also thinking bright emitter valves (French TM) were originally fitted.
What do folks think?
Lawrence.







