A bit more on this, it has been suggested on another forum that it might be a bridge due to the number of coils in the unit, not too sure on that yet, I've done some more reverse engineering, don't want to be too specific on the full circuit traced so far as it might come across as a bit complicated, the upshot of this so far is that it might be a multi band TRF regenerative receiver, if so I think it might be a bit of rare beast.
So far the circuit as traced suggests an antenna input to a multi range tuned circuit, there are two separate inductors, you can see them in one of the pics in an earlier post, the left hand one is a single coil, my guess is that one is for the highest band, the one on the right hand side appears to be multi tapped, that coil as a guess covers the other bands down to the lowest band.
The above mentioned tuned circuit (s) appear to be connected via a band change switch to the grid of an RF amp (Mullard PM1 HF) The anode of that valve is also tuned, there are four separate single coils for that, all selected by another band switch, they might be switched individually or in combination, not got that far yet, that tank circuit is capacitively coupled to the grid of a detector which is a Mullard valve of an unknown type (Poss another PM1 HF) The grid has a grid leak resistor from the grid to one side of the filament it's labeled as 3 ohms using the ohms symbol, my guess is that it's supposed to be 3 meg. The anode of that stage is in series with an other RF coil and the primary of an interstage transformer, the RF coil is a single inductor, physically it's in between the two inductors mentioned in para 2, it rotates on shaft that's brought out to the front panel, the scale is numbered 90 through to 0 through to 90 again (180 degree swing in total)
I've seen a regen circuit for that type of arrangement before, feedback from the second stage to the first stage that is, but for the life of me I can't think where at the moment, I'm sure I'll come up with it at some point.
The secondary of the 1st interstage transformer looks as though it connects to a GB battery and looks to be the usual arrangement it feeds a Mullard PM2, that in turn feeds another interstage transformer through to the AF output valve which feeds the 'phones, the make and number of that valve is unknown at the moment.
As it stands it all makes sense to me so far....Except the switchable filament arrangements for the RF and Det valves as mentioned in a previous post.
Any thoughts on this would be most welcome.
Thanks for all comments so far.
Lawrence.
So far the circuit as traced suggests an antenna input to a multi range tuned circuit, there are two separate inductors, you can see them in one of the pics in an earlier post, the left hand one is a single coil, my guess is that one is for the highest band, the one on the right hand side appears to be multi tapped, that coil as a guess covers the other bands down to the lowest band.
The above mentioned tuned circuit (s) appear to be connected via a band change switch to the grid of an RF amp (Mullard PM1 HF) The anode of that valve is also tuned, there are four separate single coils for that, all selected by another band switch, they might be switched individually or in combination, not got that far yet, that tank circuit is capacitively coupled to the grid of a detector which is a Mullard valve of an unknown type (Poss another PM1 HF) The grid has a grid leak resistor from the grid to one side of the filament it's labeled as 3 ohms using the ohms symbol, my guess is that it's supposed to be 3 meg. The anode of that stage is in series with an other RF coil and the primary of an interstage transformer, the RF coil is a single inductor, physically it's in between the two inductors mentioned in para 2, it rotates on shaft that's brought out to the front panel, the scale is numbered 90 through to 0 through to 90 again (180 degree swing in total)
I've seen a regen circuit for that type of arrangement before, feedback from the second stage to the first stage that is, but for the life of me I can't think where at the moment, I'm sure I'll come up with it at some point.
The secondary of the 1st interstage transformer looks as though it connects to a GB battery and looks to be the usual arrangement it feeds a Mullard PM2, that in turn feeds another interstage transformer through to the AF output valve which feeds the 'phones, the make and number of that valve is unknown at the moment.
As it stands it all makes sense to me so far....Except the switchable filament arrangements for the RF and Det valves as mentioned in a previous post.
Any thoughts on this would be most welcome.
Thanks for all comments so far.
Lawrence.







