16-11-2015, 01:38 PM
I may as well round this tale off.
With two 1N4007s and a 270Ω resistor the HT started out at 500V before dropping to near as damn-it its correct value, the slight difference was probably down to my using an AVO 8 instead of a 7.
While doing these tests I spotted that the electrolytic can had been re-stuffed. This was alarming as, not only had I no recollection of doing it, but the only 15µF caps I've ever had are 350V ones. I therefore decided to see about fitting an EZ80 as I mentioned in my previous post.
Rectifying and smoothing the 5V heater supply gave just shy of 7V off load but this dropped to 3.4V on load so that idea was a failure.
Luckily, through the good offices of a true pal, I obtained a 5Z4, which is what this set has actually had ever since I bought it.
With that installed the HT still started out at 480V and settled to 410V on the Reservoir. It must have always done this which says a lot for the quality of the 350V capacitors which I'd got from Farnell's which still tested fine for leakage and ESR.
It seems that anything rated above 450V is very thin on the ground and 15/16µF very scarce indeed. I was thinking that pairs of 32µF ones in series would be the way to go. I then occurred to me that a series-parallel arrangement of the 15µF ones I'd got would work just as well, and there was plenty of room in the can.
This may seem like monstrous profligacy but I'd got these cheap when they were on offer and I can't see myself wanting them for anything else so in they went and all is well.
While I was working on it I also disconnected the Extension Speaker sockets as these are for one fitted with an OPT. This means there's HT on them and as the chassis is earthed they are effectively 'Live.' Besides that I may well forget in the future and connect an 3Ω speaker to them directly, which would be exciting.
The thing that's got me a bit puzzled is the voltages on the EL33. I always thought that the Screen should be at or slightly below the potential of the Anode whereas on this set it's 23V higher.
— Joe
With two 1N4007s and a 270Ω resistor the HT started out at 500V before dropping to near as damn-it its correct value, the slight difference was probably down to my using an AVO 8 instead of a 7.
While doing these tests I spotted that the electrolytic can had been re-stuffed. This was alarming as, not only had I no recollection of doing it, but the only 15µF caps I've ever had are 350V ones. I therefore decided to see about fitting an EZ80 as I mentioned in my previous post.
Rectifying and smoothing the 5V heater supply gave just shy of 7V off load but this dropped to 3.4V on load so that idea was a failure.
Luckily, through the good offices of a true pal, I obtained a 5Z4, which is what this set has actually had ever since I bought it.
With that installed the HT still started out at 480V and settled to 410V on the Reservoir. It must have always done this which says a lot for the quality of the 350V capacitors which I'd got from Farnell's which still tested fine for leakage and ESR.
It seems that anything rated above 450V is very thin on the ground and 15/16µF very scarce indeed. I was thinking that pairs of 32µF ones in series would be the way to go. I then occurred to me that a series-parallel arrangement of the 15µF ones I'd got would work just as well, and there was plenty of room in the can.
This may seem like monstrous profligacy but I'd got these cheap when they were on offer and I can't see myself wanting them for anything else so in they went and all is well.
While I was working on it I also disconnected the Extension Speaker sockets as these are for one fitted with an OPT. This means there's HT on them and as the chassis is earthed they are effectively 'Live.' Besides that I may well forget in the future and connect an 3Ω speaker to them directly, which would be exciting.
The thing that's got me a bit puzzled is the voltages on the EL33. I always thought that the Screen should be at or slightly below the potential of the Anode whereas on this set it's 23V higher.
— Joe






