Sectional drawing with dimensions, took me a while to draw this one.... :
EDIT: Whoops...Will try again
Lawrence.
EDIT: Whoops...Will try again
Lawrence.
|
Recepteur Type RI 221
|
|
Sectional drawing with dimensions, took me a while to draw this one.... :
EDIT: Whoops...Will try again Lawrence.
Gave the receiver a quick scrub up with some meths and wax polish to get a rough idea what it would look like if restored, the front panel and knobs seem to respond to the treatment ok, managed to get a shine on the front panel, only cleaned the front face of the knobs, the cabinet base is hanging, the cabinet sides and top came up good to what they were, some staining, not sure how deep, if it's deep I would be inclined to leave it at that, all part of the history, I think the salvageable wood would respond to a full strip and re polish.
The white paint in the engraving had mostly turned to white dusty stuff, the cleaning has removed some of that, the engraving is not too clear as a result, the depth of the engraving seems not to have altered so might respond to the paint stick treatment to highlight it again, cleaning the crud off revealed a couple more engraved words and some circular arrows above the rheostat knob..."Chauff Aug"...crank up the heat or something like that. I think the front panel and the valve panel would come up very well if all the component bits were removed to give decent access. The bit of the control panel that was broken off (Top RH side) has just been loose laid back in position, the break looks clean so should glue up ok if required. Note: The six holes in the base line up with the six terminals on the control panel. Lawrence.
28-12-2015, 07:41 PM
That's looking much more promising.
I don't think I'd be brave enough to remove everything for a rebuild, but ......... Alan
Here's a photo of a receiver?
80 volts and 4 volt, the terminals are marked the same as the ones in the receiver I have, and the common connection is the same eg: 80 volts -ve to 4 volts +ve. Any ideas for the receiver in the photo? http://www.doctsf.com/forum/viewtopic.php?f=5&t=9717&p=64726 Lawrence.
30-12-2015, 12:50 PM
Just found out that the hole in the panel for the slow motion/fine tuning was for the insertion of a long ebonite rod to reduce hand capacity effects, courtesy of a member of a French radio forum.
I could be wrong but at the moment I'm thinking that Radio Industries (La Radio Industrie, Paris) might be the manufacturer. Lawrence.
30-12-2015, 03:57 PM
Cheers Gary, still not sure of the manufacturer for certain, joined a french radio forum, a few replies but nothing definate yet, computer drawings were done on a freebie package (Inkscape) that's been on my computer for a number of years,needed to familiarize again but turned out ok.
Lawrence.
31-12-2015, 09:00 AM
(This post was last modified: 31-12-2015, 09:01 AM by Radio Fixer.)
If you would like to put it all together with some words (most already written on here) the BVWS would very much appreciate it. Always short of copy !! No need to be a member. Do you intend to try to get it working? I may have early triodes?
31-12-2015, 09:36 AM
Gary, I'm not too good at writing articles, having said that the research stuff is right up my street, as to getting the receiver working I'm not sure at this stage, the reasons being several, I suppose the primary reason is that it's not mine to work on and at the moment I'm unsure of what the owner wants to do with it.
I'm also devoid of any kit with which to work on receiver's at the moment, that includes space in the house, lot's of other things going on at the moment for me, hopefully springtime will give us a bit more breathing room. If I did do a write up for publication I would prefer to know who the maker of the receiver was. I'm not discounting doing a write up, it's just that I can't commit to anything at the moment. Lawrence. |
| Users browsing this thread: |
| 1 Guest(s) |