07-06-2012, 04:40 PM
Hi,
Thanks Mark R. The desk is a lovely bit of furniture and sits well in our newly decorated hall; it's all coming together slowly; I enjoy this kind of work as it is so rewarding and unlike when I was in active conflict now that I'm retired I can relax and take my time only hampered by the terrible climate.
I might be in for some unexpected problems David regarding the new monitor please see below.
Thanks for the kind words Rob; I think you had better join the queue if you want one making. I’m looking forward to seeing it completely finished in the near future and being put to good use.
I fully agree with you Mark H regarding Oak being a beautiful timber. Oak is actually a difficult timber to work with as it is so tough and at cuts it splinters out badly unless cutters are sharp; it can be worked with hand tools but it is hard going and again the tools must be always sharp. Finishing Oak also poses a number of problems due to it's open grain; it's not a good timber to French polish. It accepts stain readily and the old method of fuming using .880 Ammonia is very effective at giving a whole range of lovely browns from light to almost black depending on exposure to the ammonia fumes. Fuming doesn't raise the grain and is done in a “fuming tent” to retain the fumes; as a test whilst fuming a stick of the same oak being fumed is placed in the tent and this stick can be withdrawn at will to determine level of fuming. I've never used oak previously on a big piece of furniture due to it being expensive as I've had access to cheap offcuts of Meranti so worked with this.
Oh dear Mark; you've surprised me with your information regarding connecting a new monitor onto my old computer; it shows how clued up I am on such matters as I expected the monitor to simply “Plug and play”. Many thanks for your offer of help and I'll be happy to accept if the need arises in fact if I do suffer problems I'll add a new thread then the information will possibly be of use to other members who also wish to upgrade their monitor.
The monitor has now arrived which is rapid service from ebuyer and looks totally different to my old CRT monitor. Adding the base was simple it being held in place by a single screw but connecting up is a disaster as the cables don't match the sockets; the only cable that connects is the mains cable. What I don't want to do is waste a lot of time and perhaps money upgrading my old computer to accept the new monitor as I intended to buy a new computer at Christmas anyway so perhaps I'll buy the new computer in the near future and hopefully this will allow easy connection?
I'm not in a hurry as my old computer is still working fine and the new monitor is now sitting in pride of place on the new desk safely out of the way.
Thanks for the reply Gary; yes the computer will sit in the left hand desk base unit; I made this unit with a much bigger opening to allow for any future updates regarding tower size. Also you are correct about the right hand base unit; I decided to add a shelf into this unit and the unit can be used for storing consumables and printer paper etc. NO secret handles either Gary it's just that I haven't yet settled on a design for the new drawer and door knobs/handles but I will do so shortly.
Base unit door in sash cramps.
The Evolution mitre saw still isn't cutting perfectly; mitres are being cut by setting the blade and fence to a set square and the cross cuts are still slightly out; normally this won't be too much trouble but when top class joints are needed this is hopeless as the slightest error stands out. Once the desk is completed I will spend some time trying to set this saw up to cut accurately. For the inner door 18mm MDF backing panel I resorted to my accurate Startrite saw bench adding the sliding table attachment; for those who have never seen such an attachment a picture is included; The table simply locates onto guide rails and runs on a set of rolling element bearings; I set this machine up when I rebuilt it many years ago and it still gives good results. The reason I've not been using it much is one of space as I've been using this machine as a table. The crown guard is removed whilst working with the sliding table but the riving knife is always in position. Rebates and trenching operations are easy with the sliding table fitted.
Sliding table fitted.
This morning I assembled and glued up the new base unit door and it is now sitting in a pair of sash cramps until the glue sets but I've put the car into the garage in disgust as this miserable weather just won't let up; it's been raining again all day and forecast to become worse later today. Even if it snows tomorrow I'm having a day in the garage. I try my best to look on the positive side of things but this climate is something else; sorry to moan.
Kind regards, Col.
Thanks Mark R. The desk is a lovely bit of furniture and sits well in our newly decorated hall; it's all coming together slowly; I enjoy this kind of work as it is so rewarding and unlike when I was in active conflict now that I'm retired I can relax and take my time only hampered by the terrible climate.
I might be in for some unexpected problems David regarding the new monitor please see below.
Thanks for the kind words Rob; I think you had better join the queue if you want one making. I’m looking forward to seeing it completely finished in the near future and being put to good use.
I fully agree with you Mark H regarding Oak being a beautiful timber. Oak is actually a difficult timber to work with as it is so tough and at cuts it splinters out badly unless cutters are sharp; it can be worked with hand tools but it is hard going and again the tools must be always sharp. Finishing Oak also poses a number of problems due to it's open grain; it's not a good timber to French polish. It accepts stain readily and the old method of fuming using .880 Ammonia is very effective at giving a whole range of lovely browns from light to almost black depending on exposure to the ammonia fumes. Fuming doesn't raise the grain and is done in a “fuming tent” to retain the fumes; as a test whilst fuming a stick of the same oak being fumed is placed in the tent and this stick can be withdrawn at will to determine level of fuming. I've never used oak previously on a big piece of furniture due to it being expensive as I've had access to cheap offcuts of Meranti so worked with this.
Oh dear Mark; you've surprised me with your information regarding connecting a new monitor onto my old computer; it shows how clued up I am on such matters as I expected the monitor to simply “Plug and play”. Many thanks for your offer of help and I'll be happy to accept if the need arises in fact if I do suffer problems I'll add a new thread then the information will possibly be of use to other members who also wish to upgrade their monitor.
The monitor has now arrived which is rapid service from ebuyer and looks totally different to my old CRT monitor. Adding the base was simple it being held in place by a single screw but connecting up is a disaster as the cables don't match the sockets; the only cable that connects is the mains cable. What I don't want to do is waste a lot of time and perhaps money upgrading my old computer to accept the new monitor as I intended to buy a new computer at Christmas anyway so perhaps I'll buy the new computer in the near future and hopefully this will allow easy connection?
I'm not in a hurry as my old computer is still working fine and the new monitor is now sitting in pride of place on the new desk safely out of the way.
Thanks for the reply Gary; yes the computer will sit in the left hand desk base unit; I made this unit with a much bigger opening to allow for any future updates regarding tower size. Also you are correct about the right hand base unit; I decided to add a shelf into this unit and the unit can be used for storing consumables and printer paper etc. NO secret handles either Gary it's just that I haven't yet settled on a design for the new drawer and door knobs/handles but I will do so shortly.
Base unit door in sash cramps.
The Evolution mitre saw still isn't cutting perfectly; mitres are being cut by setting the blade and fence to a set square and the cross cuts are still slightly out; normally this won't be too much trouble but when top class joints are needed this is hopeless as the slightest error stands out. Once the desk is completed I will spend some time trying to set this saw up to cut accurately. For the inner door 18mm MDF backing panel I resorted to my accurate Startrite saw bench adding the sliding table attachment; for those who have never seen such an attachment a picture is included; The table simply locates onto guide rails and runs on a set of rolling element bearings; I set this machine up when I rebuilt it many years ago and it still gives good results. The reason I've not been using it much is one of space as I've been using this machine as a table. The crown guard is removed whilst working with the sliding table but the riving knife is always in position. Rebates and trenching operations are easy with the sliding table fitted.
Sliding table fitted.
This morning I assembled and glued up the new base unit door and it is now sitting in a pair of sash cramps until the glue sets but I've put the car into the garage in disgust as this miserable weather just won't let up; it's been raining again all day and forecast to become worse later today. Even if it snows tomorrow I'm having a day in the garage. I try my best to look on the positive side of things but this climate is something else; sorry to moan.
Kind regards, Col.
Happiness is a wreck of a cabinet to restore.







