04-06-2012, 07:06 PM
Hi,
Well done with the shelves Big Al they look the part; without a biscuit joiner the job would have been much more difficult and certainly more time consuming. Thank you; yes the desk looks pretty good so far and it's nice to touch; the pictures give a good idea of what it looks like but it's better to actually see it in person. Once you get the Freelander sorted out it will be a pleasure to see you again and hopefully the desk will be completed in a week or so.
Well said David. I've never liked dowels but they are used a great deal in industry where the parts are jigged ensuring perfect repetitive alignment; dowels do make a strong joint but are most unforgiving regarding alignment in a home workshop.
It was cold again in the garage this morning so I was working in my coat; at least the rain had finally stopped. Whilst shopping at Aldi this morning I noticed sets of four bar clamps at £4.99 so bought a set. These clamps are just brilliant to use; I bought two from Poundland at a pound each a couple of years ago and have been looking out for more; one of the clamps from Poundland can be seen in the foreground in the picture and both have had a lot of use.
New bar clamps.
Making and attaching the base boards has been a very time consuming job; I wanted them to look better than plain boards so relieved the bottom edges on the band-saw after first marking the cut line. Two quadrant profiles were drawn with the aid of a tin lid joining both with a straight line.
Drawing quadrants and cutting out on bandsaw.
A simple shaped cut out makes a lot of difference to the look of such items and to take it a step further I added a freehand profile on the outer top edges using a large foam drum sander mounted in an electric drill; this drum sander is fierce with a coarse grit abrasive belt fitted and covered everything very quickly in heavy dust; I donned the respirator or I would have been coughing up oak boards for days. Using the drum sander with the grain leaves little work to clean up using hand held abrasive paper.
Foam drum sander.
The quadrant bottom profiles were cleaned up on my home made 4” belt sander. Both the drum and belt sanders rapidly remove material so care is needed not to go too deep. I've used this method of adding edge detail many times and am always very pleased with the results.
Belt sanding using home made sander.
Additional strength was added using glue blocks as seen in the picture; these blocks are merely glued and clamped into position until the glue sets. The base units are open at the back so I thought it prudent to add the glue blocks; shallow back base board and mitred front base board to form a rigid box section to prevent the unit “racking”. The flat faces were scraped using the Stanley #80 and given a light sanding then all were securely glued into position and clamped until the glue had set for a few hours.
Supports being glued in.
Next job was final trimming to tidy the mating edges up at the mitres etc. My Stanley shoulder plane came in very handy as it can be worked right into an internal angle cleaning it out neatly. I love playing with all my toys and soon forgot how cold it was; a bit of planing is sure to warm me up and get the bones working as they should.
Stanley shoulder plane.
The garage was then cleaned using the vac and the desk units dusted down ready to accept varnish. A 4” foam roller was used to apply varnish to all the large MDF panels and the oak framework was varnished using a top quality Purdy paint brush. Work then had to stop in order to allow the varnish to dry so I knocked off early today for a change and as I did so the sun came out and it was warm; pity it didn't come out earlier when needed.
Base units now looking good.
Tomorrow I'll apply the final coat of varnish then the units can be brought up into the bungalow to give me working space in the garage; one of the units requires a fancy door making and fitting so this will be done shortly then I'll think about a design for the knobs. I'll be sorry to see this desk completed because it has been an excellent project.
Kind regards, Col.
Well done with the shelves Big Al they look the part; without a biscuit joiner the job would have been much more difficult and certainly more time consuming. Thank you; yes the desk looks pretty good so far and it's nice to touch; the pictures give a good idea of what it looks like but it's better to actually see it in person. Once you get the Freelander sorted out it will be a pleasure to see you again and hopefully the desk will be completed in a week or so.
Well said David. I've never liked dowels but they are used a great deal in industry where the parts are jigged ensuring perfect repetitive alignment; dowels do make a strong joint but are most unforgiving regarding alignment in a home workshop.
It was cold again in the garage this morning so I was working in my coat; at least the rain had finally stopped. Whilst shopping at Aldi this morning I noticed sets of four bar clamps at £4.99 so bought a set. These clamps are just brilliant to use; I bought two from Poundland at a pound each a couple of years ago and have been looking out for more; one of the clamps from Poundland can be seen in the foreground in the picture and both have had a lot of use.
New bar clamps.
Making and attaching the base boards has been a very time consuming job; I wanted them to look better than plain boards so relieved the bottom edges on the band-saw after first marking the cut line. Two quadrant profiles were drawn with the aid of a tin lid joining both with a straight line.
Drawing quadrants and cutting out on bandsaw.
A simple shaped cut out makes a lot of difference to the look of such items and to take it a step further I added a freehand profile on the outer top edges using a large foam drum sander mounted in an electric drill; this drum sander is fierce with a coarse grit abrasive belt fitted and covered everything very quickly in heavy dust; I donned the respirator or I would have been coughing up oak boards for days. Using the drum sander with the grain leaves little work to clean up using hand held abrasive paper.
Foam drum sander.
The quadrant bottom profiles were cleaned up on my home made 4” belt sander. Both the drum and belt sanders rapidly remove material so care is needed not to go too deep. I've used this method of adding edge detail many times and am always very pleased with the results.
Belt sanding using home made sander.
Additional strength was added using glue blocks as seen in the picture; these blocks are merely glued and clamped into position until the glue sets. The base units are open at the back so I thought it prudent to add the glue blocks; shallow back base board and mitred front base board to form a rigid box section to prevent the unit “racking”. The flat faces were scraped using the Stanley #80 and given a light sanding then all were securely glued into position and clamped until the glue had set for a few hours.
Supports being glued in.
Next job was final trimming to tidy the mating edges up at the mitres etc. My Stanley shoulder plane came in very handy as it can be worked right into an internal angle cleaning it out neatly. I love playing with all my toys and soon forgot how cold it was; a bit of planing is sure to warm me up and get the bones working as they should.
Stanley shoulder plane.
The garage was then cleaned using the vac and the desk units dusted down ready to accept varnish. A 4” foam roller was used to apply varnish to all the large MDF panels and the oak framework was varnished using a top quality Purdy paint brush. Work then had to stop in order to allow the varnish to dry so I knocked off early today for a change and as I did so the sun came out and it was warm; pity it didn't come out earlier when needed.
Base units now looking good.
Tomorrow I'll apply the final coat of varnish then the units can be brought up into the bungalow to give me working space in the garage; one of the units requires a fancy door making and fitting so this will be done shortly then I'll think about a design for the knobs. I'll be sorry to see this desk completed because it has been an excellent project.
Kind regards, Col.
Happiness is a wreck of a cabinet to restore.







